AMPEROMETRIC TRANSFORMERS

DOWNLOAD OUR CURRENT TRANSFORMERS CATALOGUE

CURRENT TRANSFORMERS AND ROGOWSKI COILS

PECTECH has in stock various models of current transformers to be combined with your network analyzers or to be connected to those managed by us. The choice depends on the type of application you have to deal with, a machine rather than a retrofit on an existing panel, or the need for a solution that can fit even without having carried out an inspection.

We can suggest you and provide different solutions from the classic CTs with closed loop to those that can be opened with secondary 5A, or the more practical 333mV. Depending on the size of the conductor or the bar, we cover a few to thousands of amps. An increasingly used solution is the Rogowski probe, which is wrapped in air, rather than on a ferrous core, which does not have the problems of saturation of classical CTs. With this probe we can cover a measurement range from 10 A up to thousands of Amp with the same probe.

The compact size and low weight allow the use in any installation, on the other hand it is a more expensive solution than the current transformers that can be opened for amperages below 300 A.

CURRENT TRANSFORMERS

We supply devices and sensors for measurements on plants, machine tools, buildings and wherever there is a need to acquire and monitor processes and energy consumption.

CURRENT TRANSFORMERS Mod. SCT

SPLIT CORE VERSION WITH 333mV – 5 A SECONDARY

For versions with 333mV secondary, 5A up to 50A primaries are available with a 10mm through hole, from 80 up to 200A with a 16mm through hole, from 100 up to 300A with 24mm hole, from 300 to 600 A with 36mm hole.

The big advantage of a 333mV secondary is the small section of the cable and the possibility of extend the secondary cable (even tens of meters) without affecting the measurement accuracy. On the other hand, the 5 A version is the most used and common, associated with all the instruments available on the market and also for MID certified versions. These models are all supplied with 1m of integrated cable.

5A SECONDARY – HOLE DIAMETER 24 mm - 36 mm
  • Compatible with any analyzer with a 5A TA input
  • Allow easy installation without load shedding
  • Ideal for retrofit and energy monitoring
Hole diameter 24 mm for current from 100 A up to 300 A
Hole diameter 36 mm for current from 300 A up to 600 A.

We recommend the version with 333mV secondary for installations away from the Energy meter.

TRASFORMATORI AMPEROMETRICI
TRASFORMATORI AMPEROMETRICI
333mV SECONDARY – HOLE DIAMETER 10/16/24/36 mm
  • Easy to install and cost effective solution
  • Ideal for retrofit and energy monitoring activities
Hole diameter 10 mm for current up to 50A
Hole diameter 16 mm for current up to 200A
Hole diameter 24 mm for current up to 300A
Hole diameter 36 mm for current up to 600A
Recommended version for installations distant from the energy meter
333mV SECONDARY – HOLE DIAMETER 19x19 mm
  • Easy to install and cost effective solution
  • Ideal for retrofit and energy monitoring activities
  • Interlocking opening
  • Complete with 2 mt of integrated cable

Versione consigliata per installazioni distanti dall’analizzatore

TRASFORMATORI AMPEROMETRICI
DOWNLOAD OUR CURRENT TRANSFORMERS CATALOGUE

CURRENT TRANSFORMERS Mod. DBP

BUSBAR SPLIT CORE VERSIONS

In the case of measurements on bars, the diameter of 24 mm or 36 mm is sometimes not sufficient, in this case the solutions available are larger openable CTs with rectangular or square windows as needed.

The available sizes are 20x30 mm for current up to 300 A, 50x80 mm for current from 300 to 1000 A, 80x80 mm from 300 to 800 A, 80x120 mm for current from 600 to 2000 A and the largest 80x160 mm for current from 2000 to 6000 A. All these Transformers are available only secondary 5 A or 333mV (on demand). If your instrument supports Rogowski probes, the cost and dimensions of this solution are certainly advantageous compared to classic CTs.

SECONDARIO @ 5A

Busbar finestra 20x30 50X80 80X80 mm

Connettori sul secondario: Doppia vite M4

Copertura terminali integrata

Materiale custodia autoestinguente Nylon IEC185 secondo V0 UL-94

TRASFORMATORI AMPEROMETRICI
TRASFORMATORI AMPEROMETRICI

Busbar finestra 80X120 - 80X160 mm

Connettori sul secondario: Doppia vite M4

Copertura terminali integrata

Materiale custodia autoestinguente Nylon IEC185 secondo V0 UL-94

DOWNLOAD OUR CURRENT TRANSFORMERS CATALOGUE

CURRENT TRANSFORMERS Mod. CT

SOLID CORE VERSIONS

This type of CTs are the most known and widespread, they are mainly used on realizations from scratch and where the load shedding is not critical. It is the most economical solution and with better performances than the split core solutions, on the other hand they are less practical. Depending on the application there are multiple sizes and measurement ranges available, the choice is made mainly based on the size and type of conductor.

Stock models start at 50 A with a hole from 20 mm up to 1000 A with a 30 mm hole. As for the openable ones, as you go up in size and amperage, it is advisable to make evaluations of economy and practicality with the openable versions. The standard is the secondary at 5 A, it is possible to request versions with secondary 1 A (more expensive and with supply times of about 2 weeks).

5A SECONDARY – HOLE DIAMETER 20 - 30 mm
  • ABS Self-extinguishing
  • CASE CURRENT AT SECONDARY 5 A (others on request)
  • SAMPLING FREQUENCY 40-60 Hz
  • DYNAMIC CURRENT OF SHORT CIRCUIT (Idin) 2.5 I ter for 1 sec - Maximum peak value that the CT can withstand with the secondary in short circuit
  • NOMINAL THERMAL CURRENT OF SHORT CIRCUIT (Iter) 40-80 Ipn for 1 sec - Maximum effective value with secondary in short circuit
  • PERMANENT OVERCURRENT 1.2 In
  • REFERENCE VOLTAGE FOR INSULATION 0.72kV maximum voltage value
TRASFORMATORI AMPEROMETRICI
  • TEST VOLTAGE 3kV at 50 Hz for 1 min., Maximum voltage value between primary and secondary
  • SAFETY FACTOR N <= 5 Saturation factor (Sf) or ratio between the value of the primary current, which causes the saturation of the magnetic core, and the value of the nominal current. The lower the value of N, the greater the protection of the instrument
  • OPERATING TEMPERATURE -25 ° ... + 50 ° C STORAGE
  • TEMPERATURE -40 ° ... + 80 ° C MAXIMUM CABLE
  • TEMPERATURE 70 ° C
  • RELATIVE HUMIDITY 90% max, non-condensing
  • INSULATION in air class E
  • PROTECTION DEGREE IP 30
  • CONSTRUCTION According to CEI 38-1, IEC 185, VDE 0414, EN60044-1, EN60044-1A
BUS BAR CURRENT TRANSFORMERS
DOWNLOAD OUR CURRENT TRANSFORMERS CATALOGUE

CURRENT TRANSFORMERS Mod. RC

FLEXIBLE ROGOWSKI COILS

The Rogowski probes have the great advantage of being able to cover a very wide measurement range, from ten to tens of thousands of Ampere. The output is in mV / kA.

These probes cannot be used by all measuring instruments as the output signal must be "integrated" as it is out of phase and not linear. It is possible to use external integrators to be able to use the Energy meter probes with 333mV secondary, while still ensuring good accuracy. We have two different models, a flexible Mini Rogowski with a diameter of 36mm, suitable for measurements up to 1000 A and the bigger version for industrial needs with diameters from 85 to 300mm.

FLEXIBLE ROGOWSKI COILS Ø12MM
  • Measuring range up to 100kA.
  • Calibrated at 1%.
  • Ideal for retrofit and monitoring activities in the absence of installation spaces.
  • Easy to install, practical interlocking connector.
  • Possibility of custom realizations, length and colors.
  • Always to be used with an integrator (integrated on the Energy meter or external).
TRASFORMATORI AMPEROMETRICI
FLEXIBLE MINI ROGOWSKI COIL Ø6MM
  • Calibrated at 0.5%
  • 6mm coil section
  • Easy to install, cable fixing system with strap
  • Very competitive price.

MAIN FEATURES:

  • Excellent linearity of measurement up to 1000 A
  • Wide measurement range
  • Reduced probe size, ideal for limited spaces
  • No danger of open circuits on the secondary
  • No damage from overloading
  • Non-intrusive measurement system
DOWNLOAD OUR CURRENT TRANSFORMERS CATALOGUE

CURRENT TRANSFORMERS Mod. HSCT

AC/DC CURRENT TRANSFORMERS

This type of Current Transformers is not used in combination with the Energy meters and Network Analyzers, but is used for the measurement of DC current.

The main markets are those of photovoltaics, telecommunications, data centers, batteries, charging stations for electric vehicles. Both openable and closed versions with analogue and RS485 Modbus RTU output are available. The measurement ranges start from 50 A up to several thousand Amperes depending on the need, in the case of measurement of Energy in DC dedicated instruments are available.

SPLIT CORE HALL EFFECT SENSORS – HOLE DIAMETER 21mm/41mm

The HSCT series sensors allow the measurement of direct and alternating currents with excellent precision and a wide measurement range.

Using the open loop Hall-effect measurement technique, they allow the use of an openable core, making the sensors easy to install without disconnecting the conductors. Removable screw terminal blocks make installation extremely convenient.

DOWNLOAD OUR CURRENT TRANSFORMERS CATALOGUE

START YOUR PROJECT NOW

Pectech is your trusted partner in the instrumentation sector, we can follow you step by step in all your projects